If you find it again, the bathroom floor - which means the inclusion of your tile, sheet vinyl or ceramic tile and underlayments you should make sure that there are no signs of water damage on the floor and check whether it so firmly. In setting a new floor, the main question is always "I can tile over the existing floor or do I pick up the old first?"
If the floor is level and sound you can normally only tileRight about it with plastic or vinyl flooring,
But keep in mind how mush room you) for the bathroom door, door frame and wall molding compounds (if any: you have to open or close the door from time to time!
If the subfloor is solid, level finish, but you can not fill leveling embossers (like mortar) in subordinate positions to be on a flat surface to make, otherwise a new ¼ "underlayment about it if you can. I'm a doctor Homeowners seen ' it up "level, with thin wooden strips- Do not do it! All materials must be water and moisture resistant as possible. Always use a minimum of 3 m in height to the surface is not inclined to assure in any way.
For a typical ground floor of the house like a ranch without a basement, ground foundations framed "are", that is sitting on the floor beams with 2-by's () still images, perpendicular to the beam along the foundation. "Support beams (metal rods), at or near the center of the bar help. Shall Before drafting theSubsoil, usually a 3 / 4 "tongue and groove chipboard, plywood or similar material. Above that there is a1 / 4" plywood or cement board (insensitive) to moisture, which is called the subsoil and may also have a piece of roofing felt or similar material for extra cushioning. Be especially careful if using subsoil above the floor, as the ground can crack if the game is on, it seems best to stagger the seams.
Ceramic Tile: Since this type of tilehas become popular in the kitchen, bathrooms, halls and lounges for its durability and style, I would like to dedicate this section to this issue.
Change install ceramic tiles in the bathroom is the amount of fixtures such as toilets, sinks and vanity cabinets and doors and the next room, it is best to remove everything and start from scratch. This means removing the old and the subsoil. You need a flat surface or the tiles will create crack or break.Most ceramic tile is ¼ "thick, so that you have added up to ¾" to condition the old floor, you were made of plastic or vinyl record from the beginning. They will set off the amount of the old fittings and the door so a little trimming may be necessary (if you replace valve-no problem).
The best results, follow these steps: * With a 3ft level to check whether the ground during * Define a set of tiles with spacers (cross-shaped inserts forJoints) along the length and width to determine the space to use as many tiles you. This is to see how many tiles you need to make cuts in the vicinity of walls. * Lay Cement Board, tailored suits and the area used a small layer of mortar, put on board screed. Use screws instead of every 6 to 8 inches to secure the edges of the boat. Use mesh tape over the seams and with a thin layer of mortar. * Apply with a trowel mortar about every 3 1 / 2 "at a time and smooth applicationeven blows. * Set the full ceramic tiles at a point farthest from the door and press firmly with a rubber hammer tapping spreads so evenly. Have the cut tiles ready for you to put away from the wall and go as you. * Insert at the end of the cross-shaped spacers between the tiles to assure even rows. Standoffs at the corners and the Po tiles lay flat on the corners (do not worry, it will be equal to). You can also use the spacers to stand upright against the wall.* If you are to the closet flange (toilet hole) in the soil, you need a tile nipper or tile saw to cut a part of the circle. Do this for all sides and lay down as before. * If you have all the pieces, you must wait until a least a day not to "set" properly - that is an important step before you put the joints. When you are ready mix tile mortar around a quarter of the space in a time when you do this time to right. Take the cross spacers and apply grout with aGrout float, float operation then pull the trigger in a corner of the excess grout. Do this step with the rest of the room. * The final step is to moisten a clean sponge with water and wipe the access mortar Rinse the sponge frequently.
ไม่มีความคิดเห็น:
แสดงความคิดเห็น